Pololu Robotics & Electronics
Menu
My account Comments or questions? About Pololu Contact Ordering information Distributors
A4988 regulated and unregulated problem ( 2 ) [Motor controllers/drivers and motors] (31)
Pololu 3pi dead [Robots] (16)
Can't open device "/dev/ttyACM0": Permission denied [Robots] (14)
Using Pololu USB AVR Programmer v2 to load bootloader on to Adafruit Pro Trinket 3V [Other Pololu products] (13)
MinIMU-9 v5 and AHRS questions [Sensors] (11)
Servo not moving arm - will turn on light [Servo controllers and servos] (17)
Need a bit of help with pwr distribution motor board for Romi [Motor controllers/drivers and motors] (20)
Rc battle bot [Robots] (17)
Motor controls disabled when servo attached [Motor controllers/drivers and motors] (19)
Is Pololu USB AVR Programmer v2 compatible with the Arduino IDE? [Other Pololu products] (13)
Pir sensor used with mini maestro [Servo controllers and servos] (16)
Adjustable 4-12V Step-Up Voltage Regulator U3V50ALV [Voltage regulators] (16)
Will Dual VNH5019 driver how to connection [Motor controllers/drivers and motors] (12)
#2134 Low-Voltage Stepper Driver Not working [Motor controllers/drivers and motors] (17)
Reading WORTIME0/1 [Wixel] (13)
Stepper stopped stepping [Motor controllers/drivers and motors] (10)
18v15 Simple High-Powered Motor Controller Raspberry Pi [Motor controllers/drivers and motors] (11)
How to take multiple readings from 11 sensors [Servo controllers and servos] (12)
D24V150F5 No Output [Voltage regulators] (14)
X-y joystick and two servos [Servo controllers and servos] (10)
Simple High-Power Motor Controller (SMC) 18v25 [Motor controllers/drivers and motors] (10)
No servo movement in the control panel [Servo controllers and servos] (11)
Adding switches to the servo controllersv [Servo controllers and servos] (10)
Stepper motor not moving for small angles (<= 3 degrees) [Motor controllers/drivers and motors] (11)
G2 Motor Driver Current Feedback [Motor controllers/drivers and motors] (11)
Push Button command needed [Servo controllers and servos] (10)
No output 24V12 [Motor controllers/drivers and motors] (10)
Labview with Jrk 12v12 USB Motor Controller with Feedback [Motor controllers/drivers and motors] (12)
Countdown [Robots] (11)
MinIMU V3 Oscillations [Sensors] (11)
Voltage Regulator VOUT bouncing all over [Voltage regulators] (11)
Tic Stepper Motor Controller wit Adafruit Huzzah ESP8266 [Motor controllers/drivers and motors] (17)
Balboa Robot cannot connect to the windows [Robots] (11)
Pololu Basic SPDT Relay #2804 with r/c receiver and transmitter [Other Pololu products] (17)
Multiple stepper motors controlled by a PC [Motor controllers/drivers and motors] (15)
Creating a pid with vhdl [Motor controllers/drivers and motors] (16)
Mini Maestro 12 USB Problem [Servo controllers and servos] (13)
Pololu 18v25 CS motor driver fault flags [Motor controllers/drivers and motors] (11)
VL53L0X settings [Sensors] (13)
Can I handle RESET state of Pololu USB AVR Programmer? [Other Pololu products] (10)
Pololu TReX DMC01 Only Flashes Red Light [Motor controllers/drivers and motors] (13)
Rc switch [Other Pololu products] (10)
No output from A1, A2, B1 or B2 from MP6500 Driver [Motor controllers/drivers and motors] (12)
3pi robot acting very strange [Robots] (11)
Correcting the Balboa magnetometer [Robots] (5)
MIRR - Interactive 98-servo installation [Share your projects] (1)
Rock-Paper-Scissors game using computer vision and machine learning on Raspberry Pi [Share your projects] (1)
Arduino UNO Line Follower ROBOT [Share your projects] (2)
Wheel encoder with Raspberry Pi 3 [Other Pololu products] (7)
Stepper Motor Maximum Frequency [Mechanical design and actuators] (4)