|
About the Motor controllers/drivers and motors category
|
|
2
|
2716
|
September 5, 2021
|
|
DRV8835 and 3S LiPo power supply
|
|
1
|
8
|
January 23, 2025
|
|
Tic Control through arduino analog output
|
|
1
|
4
|
January 22, 2025
|
|
Cannot detect I2C devive on Zyqn UltraScale+ MPSOc
|
|
3
|
56
|
January 18, 2025
|
|
MOTORON M3S550 + Arduino (not working)
|
|
1
|
12
|
January 16, 2025
|
|
Tic RC Homing
|
|
3
|
417
|
January 11, 2025
|
|
Using the Maestro and Tic with limit switch
|
|
3
|
9
|
January 10, 2025
|
|
Best practise to open and close connection to Tic Controller
|
|
1
|
13
|
January 7, 2025
|
|
Changing SDA Pin mode in software
|
|
13
|
163
|
December 18, 2024
|
|
Dual G2 High-Power Motor - Fail Safe
|
|
3
|
87
|
December 11, 2024
|
|
MG37D input/output characteristics (dead zone)
|
|
19
|
217
|
December 11, 2024
|
|
How to run an actuator with Jrk G2 21V3 digital input
|
|
2
|
57
|
December 7, 2024
|
|
Torxis Servo Issue
|
|
2
|
374
|
December 6, 2024
|
|
Motorcar
|
|
10
|
117
|
December 4, 2024
|
|
A4988 and CNC shield problem
|
|
0
|
59
|
December 3, 2024
|
|
How to properly size the additional capacitor for 24v13 and 24v21 motor drivers?
|
|
1
|
77
|
December 2, 2024
|
|
Heat sink for 24v13 and 24v21 motor drivers
|
|
3
|
85
|
November 30, 2024
|
|
VNH5019 with Audrino Uno and 2 20.4:1 Metal Gearmotor 25Dx65L mm MP 12V with 48 CPR Encoder
|
|
12
|
160
|
November 26, 2024
|
|
Motor driver error pololu 36v4
|
|
1
|
57
|
November 21, 2024
|
|
Is 3.3v output on G2 driver enough to power Pi Pico?
|
|
2
|
79
|
November 11, 2024
|
|
Coil wiring to A4988 driver
|
|
6
|
2960
|
April 12, 2015
|
|
DRV8835 Motor Driver No Output
|
|
7
|
145
|
November 6, 2024
|
|
How to wait for tic position reached
|
|
6
|
127
|
November 6, 2024
|
|
Motor Drivers for Romi Chassis and Arduino Uno
|
|
1
|
87
|
November 6, 2024
|
|
Pololu JRK G2 24v13 overheating
|
|
3
|
97
|
November 5, 2024
|
|
Two 36v4 drivers and Two Stepper motors run by Arduino Nano and PCB
|
|
1
|
68
|
November 1, 2024
|
|
5A motor with jumper connector
|
|
1
|
93
|
October 31, 2024
|
|
Using jrk2cmd's to load settings to eeprom from command line
|
|
2
|
84
|
October 31, 2024
|
|
Python code to deal with unconnected tic's
|
|
2
|
108
|
October 29, 2024
|
|
Roboclaw 2x15 not working
|
|
1
|
76
|
October 28, 2024
|
