# Arduino Due + AltIMU-10

**URL:** https://forum.pololu.com/t/arduino-due-altimu-10/6914
**Category:** Product suggestions
**Created:** [March 23, 2014, 4:09am UTC](https://forum.pololu.com/t/arduino-due-altimu-10/6914 "2014-03-23T04:09:37Z")
**Posts on this page:** 5
**Page:** 1

<div class="post-metadata">

### Author: ![Camel](https://forum.pololu.com/letter_avatar_proxy/v4/letter/c/4af34b/32.png) [@Camel](https://forum.pololu.com/u/Camel)
#### Post date: [March 23, 2014, 4:09am UTC](https://forum.pololu.com/t/arduino-due-altimu-10/6914/1 "2014-03-23T04:09:37Z")

</div>

Hello,

I’d love to have an Arduino compatible board with a SAM3X8E chip and AltIMU-10 sensors. Presently I’m using an Arduino Due and an AltIMU-10 to control a model aircraft, however I am finding the Due is very bulky and is physically not well suited for this purpose. The website for my project is [http://www.camelsoftware.com/firetail/](http://www.camelsoftware.com/firetail/)

Ideally what I am after is something with

2x I2C ports, with the AltIMU-10 sensors on one of them  
At least 3 UART serial ports  
6x 5V tolerant digital IO pins for reading from an RC receiver  
6x 5V logic level digital pins for driving servos  
An I2C EEPROM chip to store settings would be nice  
Plus a few analog pins for measuring voltages

A similar board is the FlyMaple, however it has no analog pins and less SRAM. I suppose the biggest point of difference between the FlyMaple and this proposed board is that I have autopilot software ready for it, plus a sizeable audience following the projects blog. Would Pololu be interested in developing this?

Regards, Sam

---

<div class="post-metadata">

### Author: ![JeremyT](https://forum.pololu.com/user_avatar/forum.pololu.com/jeremyt/32/540_2.png) [@JeremyT](https://forum.pololu.com/u/JeremyT)
#### Post date: [March 25, 2014, 1:38am UTC](https://forum.pololu.com/t/arduino-due-altimu-10/6914/2 "2014-03-25T01:38:07Z")

</div>

Hello, Sam.

Your project looks interesting. We are not currently interested in developing a board based on the SAM3X8E.

Good luck on your project. I would love to hear more about it. If you feel like sharing, you can post about your project in the [Share Your Projects](https://forum.pololu.com/c/robotics-and-electronics-general-discussion/share-your-projects) section of our forum.

- Jeremy

---

<div class="post-metadata">

### Author: ![Camel](https://forum.pololu.com/letter_avatar_proxy/v4/letter/c/4af34b/32.png) [@Camel](https://forum.pololu.com/u/Camel)
#### Post date: [March 25, 2014, 5:36am UTC](https://forum.pololu.com/t/arduino-due-altimu-10/6914/3 "2014-03-25T05:36:15Z")

</div>

Hi Jeremy,

Thanks for the reply. Would you consider a different chip then?

I started a thread about the project [here](https://forum.pololu.com/t/firetail-uav/6921/1).

Regards, Sam

---

<div class="post-metadata">

### Author: ![Ben](https://forum.pololu.com/user_avatar/forum.pololu.com/ben/32/30_2.png) [@Ben](https://forum.pololu.com/u/Ben)
#### Post date: [March 25, 2014, 8:16pm UTC](https://forum.pololu.com/t/arduino-due-altimu-10/6914/4 "2014-03-25T20:16:38Z")

</div>

Hi, Sam.

If we were going to make something based on a Cortex M3, it would probably be the STM32 since we have used that on other products. However, an autopilot-type product like you are talking about is a substantial development project, so while we might be interested in it at some point, it is not something we can do soon. There are also many products like this out there, so it would take a lot of work to figure out if there is even anything special we could offer.

- Ben

---

<div class="post-metadata">

### Author: ![Camel](https://forum.pololu.com/letter_avatar_proxy/v4/letter/c/4af34b/32.png) [@Camel](https://forum.pololu.com/u/Camel)
#### Post date: [March 26, 2014, 12:27am UTC](https://forum.pololu.com/t/arduino-due-altimu-10/6914/5 "2014-03-26T00:27:53Z")

</div>

Hi Ben,

Thanks for the reply, I understand.

Cheers, Sam
